FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The Culver City Owner’s Guide

We stock FAAC-compatible hinge and roller replacement parts on our trucks and install them throughout Culver City, typically for $185 to $420 depending on the model and how many rollers or hinges need attention. Most hinge and roller replacements are completed in a single visit, and we quote the full price before a single bolt comes off. The way most Culver City homeowners discover a failing hinge or roller is not through a gate that won’t open, but through a gate that scrapes, drags, or groans half a second longer than it should. Then one morning it simply will not swing at all, usually with a car waiting in the driveway.

Call (619) 350-4659

Which FAAC Models This Applies To

FAAC builds slide gates and swing gates, and the hinge and roller assembly differs sharply between the two. On FAAC swing gate operators (the 390, 400, 412, 415, S418, and 770 series), the hinge carries the full weight of a leaf that can run 400 to 900 pounds on residential estates in Culver City. On FAAC slide gate setups (the 740, 741, 844, and 884 series), the task falls to a steel V-track roller assembly, and those rollers wear against a steel track instead of pivoting on a pin. That single difference is the most common misdiagnosis we see: a homeowner buys a hinge for a slide gate or a roller for a swing gate because an online listing used loose wording. We check the FAAC model plate before ordering anything, then match the part by measuring the leaf, the gate weight, and the mounting spacing. For most FAAC residential gates, we install quality OEM-equivalent hinges and rollers. For gates that carry unusual weight, exposed coastal air, or a history of repeated hinge failures, we recommend genuine FAAC replacements. We are an independent service company, not affiliated with FAAC, and we stock compatible parts from suppliers we have worked with for decades.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate scrapes or drags on the low side. A worn hinge lets the outer edge drop, so the gate grinds against concrete or landscape rock that never used to touch it. We see this often in the Carlson Park and Studio Village neighborhoods, where older driveways have settled over the years.
• The gate groans when it moves. A roller that has lost its bearing or a hinge that has gone dry will announce itself before it fails. The sound is metal dragging on metal, not the smooth electric hum of the operator doing its job.
• The gate wobbles when it starts or stops. That side-to-side play is the hinge pin wearing the bore, or a slide gate roller developing flat spots from sitting in one position. In Culver City, where many FAAC gates open only once or twice a day, that sitting wear is more common than mileage wear.
• The gate catches partway through its travel. If the FAAC operator strains, stops, or reverses mid-cycle, the motor usually gets blamed. In a surprising number of cases we diagnose, the motor is fine and the roller or hinge has worn enough to change the geometry the operator was tuned for.
• Rust bleed or metal dust below the hinge. Orange staining on the gate post or fine dark dust on the track is the part literally shedding itself. A little surface rust is normal in coastal Culver City air; a pile of metal dust is a part in its last weeks.

Replacement Cost & What’s Included

For a typical FAAC swing gate in Culver City, replacing one leaf’s hinge set runs $185 to $320 installed. Slide gate roller replacement runs $240 to $420 depending on the number of rollers, the track condition, and whether the gate needs to be lifted off for the swap. The range is driven mostly by the gate’s weight and how much of the surrounding hardware has worn with the failed part. When you call us, we give you the installed price before work starts: part, labor, and any shimming or track adjustment, settled up front. No surprises on the bill. And because every job we do carries our 90-Day Done Right Promise in writing, if that hinge or roller is not right, we come back and make it right, no paperwork, no arguing. Victor Salinas grew up in Sunkist Park and has repaired gates in Culver City long enough to know that the hinge a homeowner notices least is usually the one doing its job perfectly. We aim for that.

DIY or Call Us?

What an owner can safely check is the obvious: visible rust, a leaf that sits visibly lower than its mate, rollers that look flattened, a track caked with debris. Cleaning the track is fine and worthwhile. What a homeowner should not attempt on a heavy FAAC gate is replacing the hinge or roller themselves. A 500-pound leaf under spring or motor tension, hanging on worn hardware, can shift suddenly when unbolted. We have taken calls from owners whose gate dropped off a floor jack partway through a hinge swap and crushed a section of track or a planter bed, narrowly missing a car. We have the lifting equipment, the shimming stock, and the habit of double-checking the operator after the parts go in, because a new hinge on an old FAAC motor that is out of tune will still fight you. If the hinge or roller is gone, call (619) 350-4659. We will tell you over the phone whether it sounds like a single visit, and what the likely price range is. Estimates are free.

Key Takeaways

• FAAC hinge and roller replacement in Culver City typically runs $185 to $420 installed.
• We stock FAAC-compatible parts on the truck: most jobs are done in one visit.
• The price is quoted and agreed before any work starts.
• Every replacement carries the 90-Day Done Right Promise in writing.
• Call (619) 350-4659 for a free estimate, 24 hours a day, 7 days a week. A live person answers.